Sponsored Links

 

 

 

1982-96 Chevrolet S-10 2wd

Source: www.fabtechmotorsports.com
Topic: Chevrolet


Short Desciption:
1983-01 Chevrolet S-10 2 Wheel Drive FTS7268-9 Front Brake Line ... brake system following the instructions in the GM shop manual. ... Service seal kits are available separately for future maintenance.

 

Content Inside:
4331 EUCALYPTUS AVE.   ~~  CHINO, CA 91710   909-597-7800    FAX 909-597-7185 1983-01 Chevrolet S-10  2 Wheel Drive FTS7268-9 Front Brake Line kit PARTS LIST: 2 EA. FRONT BRAKE LINES FT7268-9G    2 EA. FT17 00/01 FITTING ADAPTER 4 EA.CRUSH WASHERS FT44516 READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION! INSTRUCTIONS: 1. Lift up the front end of the truck and support the frame rails with jack stands. NEVER WORK UNDER AN UNSUPPORTED VEHICLE! 2. Remove both front tires.  Remove the nut securing the tie rod to the stock spindle and separate the tie rod from the spindle. Remove the banjo bolt securing the brake line to the caliper.  Separate the hard line section from the rubber brake line at the frame.  Remove the clip holding the rubber brake line to the frame tab and set aside.  Using an adjustable wrench or pliers bend the brake line tab on the frame to point the brake line away from the frame.  Insert the new brake line into the frame mount tab and reinstall the clip.  The new brake line should point parallel to the frame and the upper control arm.   Bend the tab as necessary to properly position the brake line. 3. Using the supplied crush washers attach the end of the brake line with the banjo fitting to the caliper.  Be sure there is a crush washer on each side of the banjo fitting and the old washer is not still attached to the bolt or caliper.  Do not tighten the banjo bolt.  Attach the factory hard line to the upper fitting on the new brake line.  2000-01 Use FT17 adapters.  Center the lower tube coming out of the banjo fitting with the two locating tabs on the caliper and torque the bolt enough to slightly crush the washers.  Tighten the upper fitting on the new brake line.  Turn the spindle right to left making sure the brake line does n ...

 

add to Google Reader add to Google Bookmark add to bloglines add to newsgator add to FURL add to digg add to webnews add to Netscape add to Yahoo MyWeb add to spurl.net add to diigo Bookmark newsvine Bookmark del.icio.us Bookmark @ SIMPIFY Bookmark MISTER WONG Bookmark Linkarena Bookmark icio.de Bookmark oneview Bookmark folkd.com Bookmark yigg.de Bookmark reddit Bookmark StumbleUpon Bookmark Slashdot Bookmark blinklist Bookmark technorati add to blogmarks add to blinkbits add to ma.gnolia add to smarking.com add to netvouz add to co.mments add to Connotea add to de.lirio.us

 

Related PDF Files

Ballweg Chevrolet (Flex-fuel vehicle dealership)


Topic: Chevrolet

Green & Growing Regional Bioindustry Bus Tour Ballweg Chevrolet (Flex-fuel vehicle dealership) Business /Organization: Ballweg Chevrolet Address: 3605 Laura Lane, Middleton, WI ...

2006 Chevrolet Cobalt Specifications


Topic: Chevrolet

2006 CHEVROLET COBALT SPECIFICATIONS 2006 Cobalt SS Pro Stock Cobalt PRO FWD Cobalt Body style: 2 ... fuel injection carburetors (SFI) with turbocharger Transmission: 5-speed manual 5-speed ...

200-522 INSTALLATION INSTRUCTIONS 85-91 Chevrolet Corvette 5.7L 85 ...


Topic: Chevrolet

1 # 200-522 INSTALLATION INSTRUCTIONS 85-91 Chevrolet Corvette 5.7L 85-92 Chevrolet Camaro 5.7L Parts ... Please refer to your vehicles service manual for proper adjustment. 9. Reinstall the throttle body ...

Chevrolet Silverado & GMC Sierra First Responder Guide


Topic: Chevrolet

Chevrolet Silverado & GMC Sierra First Responder Guide Page 19of 34 Disabling Procedures Disabling Procedures Today,

 

Sponsored Links